www.osram.com/ flex due to the special conditions of manufacturing processes of led, the typical data of technical parameters can only reflect st atistical figures and do not necessarily corres pond to the actual parameters of each single product which could differ from the typical data. subject to change without notice. errors and omissions excepted. version: 2014 - 05 - 06 linearlight flex ? protect advanced g2 C lf06a - p 1 / 4 linearlight flex protect advanced C lf0 6a - p technical datasheet benefits for outdoor use ? ip67 high performance silicone: ? extreme long life time: 50.000 h ? high flexibility pre mounted feeder for easy connection new: slimmer design - reduced height: 3.7 mm - elegant white appearance - electronic components hidden new: shorter pitch compared to prior generation applications ships and boats, wall integration machine lighting path illumination, illuminated signs architectural lighting quick reference product order code color k w/m lm/m lm/w shipping units lf06a - w3f - 830 - p 4008321789983 white 3000 k 5 350 70 1 / 8 lf06a - w3f - 840 - p 4008321790125 white 4000 k 5 390 78 1 / 8 lf06a - w3f - 870 - p 4008321790149 white 7000 k 5 390 78 1 / 8 technical features protection type ip 67 (outdoor use) high performance silicone high uv - resistancy saltmist proof dimmabl e pulse width modulation (pwm) binning fine white lifetime 50 , 000 h adhesive tape on backside tesa (high performance tape) fulfilled standards/tests flammability: glow - wire test with 850 C en60598 - 1 mixed gas corrosion test C iec60068 - 2 - 60 complementary systems connectsystem ip67 lp , slimconnectsystem (ip54) , slim track, optotronic 100 16.7 11 3.7 10,000 all dimensions in mm
www.osram.com/ flex due to the special conditions of manufacturing processes of led, the typical data of technical parameters can only reflect st atistical figures and do not necessarily corres pond to the actual parameters of each single product which could differ from the typical data. subject to change without notice. errors and omissions excepted. version: 2014 - 05 - 06 linearlight flex ? protect advanced g2 C lf06a - p 2 / 4 technical operating data (for overall module) product order code voltage [v] power [w] current [a] luminous flux [lm] radianc e angle [] overall length lf06a - w3f - 830 - p 4008321789983 24 50 2 3500 120 10 m lf06a - w3f - 840 - p 4008321790125 24 50 2 3900 120 10 m lf06a - w3f - 870 - p 4008321790149 24 50 2 3900 120 10 m minimum & maximum ratings operating temperature at tc - point [c] storage temperature [c] voltage range [v dc] reverse voltage [v dc] lf06a - 20 +7 0 c - 40 +100c 23 25 v 2 5 v ? exceeding maximum ratings for operating and storage temperature will reduce expected life time or destroy the led module. ? exceeding maximum ratings for operating voltage will cause hazardous overload and will likely destroy the led module. ? the temperature of the led module must be measured at the tc - point according to en60598 - 1 in a thermally constant status with a temperatu re sensor or a temperature sensitive label. for exact location of the tc - point see drawing below. technical drawing safety information ? the module has to be protected from mechanical loads ? assembly must not damage or destroy conducting paths on the circuit board. ? installation of led modules (with power supplies) needs to be made with regard to all applicable and safety standards. only q ualified personnel should be allowed to perform installations. ? observe correct polarity! depending on the produ ct incorrect polarity will lead to emission of no light. the module can be damaged after a few seconds. to prevent this, c orrect polarity immediately! (see "reverse voltage", page 2) ? parallel connection is highly recommended as saf e electrical operation mo de. serial connection is not recommended. unbalanced voltage drop can cause hazardous overload the led module. ? esd protection methods have to be observed when cutting and connecting the module. on esd handling in the application note es d protection for le d modules. ? the led module must not be operated under water ? please ensure that the power supply is of adequate power to operate the total load. 16.7 mm
www.osram.com/ flex due to the special conditions of manufacturing processes of led, the typical data of technical parameters can only reflect st atistical figures and do not necessarily corres pond to the actual parameters of each single product which could differ from the typical data. subject to change without notice. errors and omissions excepted. version: 2014 - 05 - 06 linearlight flex ? protect advanced g2 C lf06a - p 3 / 4 in order to drive osram led - modules safely, it is absolutely necessary to operate them with an electronically st abilized power supply protecting against short circuits, overload and overheating. to also ease the luminaire/installation approval, electronic control gear for led or led modules should carry the ce mark and be enec certified. in europe the declarations o f conformity must include the following standards: ce: ec 61347 - 2 - 13, en 55015, iec 61547 and iec 61000 - 3 - 2 - enec: 61347 - 2 - 13 and iec/en 62384. also check for the mark of an independent authorized certification institute. please see the relevant brochure for more detailed information (see "related and further information") osram optotronic? control gear complies to all relevant standards and guarantees safe operation. a ssembly information ? the smallest electrical unit (seu) (1 0 0 mm - 6 leds) can be removed by cutting at the printed marks at the side. ? after cutting connect the module via connectsystem ip67 lp . insert module into connector and apply pressure on a hard surface until locked. ? the mounting of the single led coupons is facilitated by means of the double - sided adhesive on the back surface of the module. care must be taken to provide a clean and dry mounting surface, free of oils or silicone coatings as well as dirt particle. the mo unting substrate must have sufficient structural integrity. ta ke care to completely remove the adhesive backing. once the module is appropriately positioned, press on the module with about 20n/cm2 (refe r to application techniques of tesa adhesive transfer tapes). to support adhesion at higher temperatures, use additi onal mounting brackets if temperature exceed s tc = 40c. ? the minimum bending radius is 5 cm. ? when installing in environments with large variations in temperature (e.g. outdoor applications) and operating length of more than 2 m, the use of adequate mountin g surfaces is necessary . otherwise it is advisable to use an additional thicker adhesive tape to absorb the stress of any mismatch in expansion. ? if temperature exceed s tc = 40c, additional mountin g brackets are needed. ? pay attention to avoid highly corrosive atmospheres , e.g. permanent high humidity or hydrogen sulfide (h2s). with current led technology, h2s is causing accelerated corrosion which will lead to shortened timelife or premature failure. sources for h2 s may be rubber, foamed rubber, soft - foam - tapes, sealings on rubber basis, natural sourc es (e.g. sulfur springs), etc. to avoid h2 s from sulfur - vulcanized rubber it is necessary to switch to silicon based materials or rubber that is peroxid - crosslinked. indication may be found in the material datasheet of the rubber supplier. complementary systems and accessories accessories type product ean shipping units connectsystem ip67 endcap for module lf - endcap ip67 lp 4052899902565 10 2pin feeder lf - 2pin ip67 lp 4052899125711 5 2pin jumper lf - 2conn ip67 lp 4052899125735 5 slim connectsystem ip54 2pin feeder l f - 2pin flex ip sc 4008321841902 10 jumper (board - to - board) (also add : 4008321841926) lf - conn flex sc 4008321832467 25 ip54 protection for jumper (4008321832467) lf - conn flex ip sc 4008321841926 25 slim track system slim track lf - lts - 2100 slim track 4008321978981 40 mounting bracket for slim track lf - lts - mb 4008321979025 35 / 280 clear slim track cover lf - lts cover c 4008321790187 40 diffuse slim track cover lf - lts - cover - diffuse 4008321979001 40 endcap for diffuse cover lf - lts - endcap 4008321979049 20 / 160 semi - diffuse slim track cover lf - lts cover s 4008321790200 40
www.osram.com/ flex due to the special conditions of manufacturing processes of led, the typical data of technical parameters can only reflect st atistical figures and do not necessarily corres pond to the actual parameters of each single product which could differ from the typical data. subject to change without notice. errors and omissions excepted. version: 2014 - 05 - 06 linearlight flex ? protect advanced g2 C lf06a - p 4 / 4 optotronic ? please consider that lengths may differ if further controls are installed. recommended optotronic? drivers ean recommended max. length per driver non - dimmable optotronic ot 6/200 - 240/24 ce 4008321113269 0,1 m - 1,2 m optotronic ot 8/200 - 240/24 4008321040169 0 m - 1,6 m optotronic ot 20/220 - 240/24 4050300618111 0,1 m - 4 m optotronic ot 20/120 - 240/24 s 4050300662626 0,2 m ? * ? - 4 m optotronic ot 75/220 - 240/24 4050300817477 0 m - 15 m ? ** ? optotronic ot 75/220 - 240/24 e 4008321362476 0 m - 15 m ? ** ? optotronic ot 80/220 - 240/24 p 4008321981684 5 m ? * ? - 16 m ? ** ? optotronic ot 120/220 - 240/24 p 4008321981707 12 m ? * ? ? ** ? - 24 m ? ** ? optotronic ot 240/220 - 240/24 p 4008321981721 24 m ? * ? ? ** ? - 48 m ? ** ? dimmable optotronic ot easy 60 ii 4008321187796 0 m - 12 m ? ** ? optotronic ot easy 80 4008321808363 0 m - 16 m ? ** ? optotronic ot 65/220 - 240/24 3dim e 4008321964403 0 m - 13 m ? ** ? optotronic oti dali 75/220 - 240/24 1 - 4 ch 4008321371560 0 m - 15 m ? ** ? optotronic ot 80/220 - 240/24 dim p 4008321981677 5 m ? * ? - 16 m ? ** ? optotronic ot 120/220 - 240/24 dim p 4008321981691 12 m ? * ? ? ** ? - 24 m ? ** ? optotronic ot 240/220 - 240/24 dim p 4008321981714 24 m ? * ? ? ** ? - 48 m ? ** ? ? * ? operation with shorter length possible. recommended minimum length to achieve optimum operating conditions . ? ** ? total lengths per driver. length of si ngle strip must not exceed 10 m. contacts & information german engineering meets italian elegance C creating a european product all linearlight flex ? protect advanced are made in italy by osram, with over 100 years of experience in light solutions. osram gmbh marcel - breuer - stra?e 6 80807 munich, germany www.osram.com +49.89.6213 - 0 sales and technical support is given by the local osram subsidiaries. on the osram website all subsidiaries are lis ted with complete address and phone numbers. osram led systems www.osram.com/led - systems osram: flexible led modules www.osram.com/flex osram catalogue http://catalog.osram.com general information www.osram.com ot C 24v l a l c l b maximim length per ot: l a + l b + l c + ? l max/ot maximum length per strip: l a b c
|
